Description
SE60 V SCREED
FULL MACHINE WARRANTY THROUGH 9/1/27, PT/HYD/TECH WARRANTY THROUGH 9/1/29 OR 5,000 HOURS.
AP1055 08A MTS ASPHALT PAVER
APRON, STR HYD FOLD, STD ENTRY
EXTENSION, 6" AUGER, PAIR
EXTENSION, MAINFRAME, POWER
FLASHING, SIDE, SHORT
FLASHING, STR HYD FOLD SE, RGD
HITCH, HYD PREP, TRACTOR
HOPPER, STD ENTRY, LOW SIDE
LANE 3 ORDER
Online Owner's Manual
PAINT, STANDARD, ANSI/ISO
PLATES, SDX SCREED, SM XL
Remaining Factory Warranty Machine still undoer facotry warranty.
SEAT, VINYL, DELUXE
SENSOR, AUG SONIC, CONV SONIC
SENSOR, GRADE, SONIC, EXTEND
TRACK, MTS, SMOOTH
VISORS, DISPLAY, TRACTOR
Control: BASE CAT G&S SYSTEM, PENDANT
Instructions: ANSI
Panel: POWER SUPPLY
Steering: SPRING RETURN
Heater: ENDGATE
Plate: STANDARD WEAR LIFE
Sensor: HOPPER MATL LEVEL/TEMP, SLOPE
Films: ANSI
Indicator: TOW POINT
Guide: STEERING
Hose: REEL WITH WAND
Umbrella: CAT
Ventilation System: NO CANOPY
Cylinder Kit: PSA
Ext: POWER FOR POWER ENDGATE
Visors: DISPLAY
Tank: WASHDOWN
Equipment-certification-code: NCR
Filters: AIR COOLER
EngineMake: CAT C7.1Specifications
Year2026
ManufacturerCATERPILLAR
ModelAP-1055
Hours825
Serial NumberP2600100
ConditionUsed
Stock NumberEQ0183300
Vibratory ScreedYes
Washdown SystemYes
Auxiliary LightingYes
Year2026|
ManufacturerCATERPILLAR|
ModelAP-1055|
Hours825|
Serial NumberP2600100|
ConditionUsed|
Stock NumberEQ0183300|
Vibratory ScreedYes|
Washdown SystemYes|
Auxiliary LightingYes|
Inspection Information
ARRIVAL AT SITE
CHECK CRITICAL FLUIDS (ENGINE OIL AND ANTI-FREEZE) BEFORE STARTINGNormal
IMPLEMENT SITE SPECIFIC SAFETY MEASURES (CHOCKS, LOCK OUT TAG OUT, ETC)Normal
PERFORM SITE SAFETY CHECKNormal
START, OPERATE AND WARM-UP MACHINE COMPONENTS (CYCLE HYDRAULIC CYLINDERS, MOVE AROUND TO CIRCULATE FINAL DRIVE, DIFFERENTIAL AND TRANSMISSION FLUIDS). THIS MAY TAKE 5-10 MINUTES TO PERFORM. IT IS IMPORTANT TO DRAW A GOOD OIL SAMPLE FROM CIRCULATED OIL. NOTE ANY USUAL NOISES AND SMOKE.Normal
TAKE PICTURES FROM ALL 4 CORNERS OF THE MACHINEPhoto Required
VERIFY S/N & HOURS OF MACHINE AND SERVICE LEVEL (TAKE IMAGE OF MONITOR)Yes
SAMPLE MACHINE
ENSURE ALL OIL SAMPLE LABELS ARE COMPLETED CORRECTLYNormal
SUBMIT ALL SOS VIA SOS INSPECTYes
TAKE OIL SAMPLE FROM HYDRAULIC, FINAL DRIVES, PUMP DRIVE AND AUGERNormal
TAKE OIL SAMPLE FROM WARM ENGINENormal
ENGINE
CHANGE ENGINE OIL AND FILTER, SAVE AND CUT FILTER AND EXAMINE FOR DEBRISNormal
CHANGE PRIMARY AIR FILTERNormal
CHECK COOLANT LEVEL AND FREEZE POINT. RECORD FREEZE POINT:Normal
INSPECT AFTERCOOLERNormal
INSPECT AIR FILTER RESTRICTION INDICATORNormal
INSPECT AIR INTAKE SYSTEM FOR LEAKSNormal
INSPECT ALL ENGINE DRIVE BELTS AND PULLEYSNormal
INSPECT BELLY PAN FOR DEBRIS BUILD UPNormal
INSPECT COOLANT HOSESNormal
INSPECT CRANKCASE BREATHER, CLEAN IF REQUIREDNormal
INSPECT ENGINE FOR LEAKSNormal
INSPECT EXHAUST SYSTEMNormal
INSPECT RADIATOR FOR DIRT BUILD UP AND LEAKSNormal
INSPECT TURBO FOR SIGNS OF LEAKSNormal
INSPECT WATER PUMP FOR LEAKSNormal
REMOVE AND CLEAN/REPLACE PRIMARY FUEL FILTERNormal
REPLACE SECONDARY FUEL FILTERNormal
HYDRAULIC
CHANGE HYDRAULIC RETURN FILTER, CUT AND INSPECT FOR DEBRISNormal
INSPECT HYDRAULIC CYLINDER CONDITION AND LEAKSNormal
INSPECT HYDRAULIC HOSE/LINES CONDITION AND LEAKSNormal
INSPECT HYDRAULIC PUMPS FOR LEAKSNormal
FRAME/CHASSIS
CHECK FRAME AND COMPONENTS FOR CRACKS/DAMAGENormal
CHECK FUEL TANK BREATHER AND CLEAN/REPLACENormal
CHECK OIL LEVELS IN; HYDRAULIC PUMP DRIVE, AUGER DRIVE GEAR BOX, DRAG CONVEYOR GEAR BOXES, CHECK DEBRIS ON MAG PLUGNormal
CHECK TRACK TENSIONERNormal
CLEAN PAVER VENTILATION SYSTEM BLOWERNormal
INSPECT AUGER DRIVE CHAINNormal
INSPECT AUGER/SCREW CONVEYORNormal
INSPECT CONVEYOR DRIVE CHAINNormal
INSPECT ROPS/FOPS STRUCTURE, CRACKS, DAMAGE AND LOOSE HARDWAREN/A
INSPECT STEPS, GRAB IRONS AND SHEET METAL CONDITIONNormal
INSPECT TRACK ASSEMBLYNormal
LUBE IDLER WHEEL BEARINGNormal
DRIVE TRAIN
CHECK FINAL DRIVES FOR LEAKS, WEAR AND DAMAGENormal
REPLACE FINAL DRIVE, AUGER, AND PUMP DRIVE OILNormal
ELECTRICAL/CAB
CHECK A/C AND HEATER OPERATION, CLEAN CAB FILTERN/A
CHECK ALL IMPLEMENT CONTROLS, WEAR AND OPERATIONNormal
CHECK ALL OPERATING LIGHTS, HEAD,FLOOD, BRAKE, TURN AND DOMENormal
CHECK CAB COMPONENTS, GLASS, DOOR, WINDOWS, FLOOR MAT, HANDLES, SWITCHES, AND CONTROLSN/A
CHECK GAUGE CLUSTER FOR OPERATIONSNormal
CHECK PRODUCT LINK OPERATIONAL STATUS, IF EQUIPPEDNormal
CHECK SEAT, SUSPENSION, CUSHIONS AND ARM RESTS, CONDITION, LOOSENESS AND OPERATIONNormal
DOCUMENT ANY LOGGED EVENTS/FAULT CODES FROM THE DASHNormal
INSPECT BATTERY, CABLES AND SWITCHESNormal
INSPECT WIPER AND WASHER FLUID PUMP, OPERATIONS, AND CONDITIONN/A
VALIDATE HOURS AND LOCATION OF MACHINE IN VISION LINK TO ENSURE ACCURACYYes
MISC
CHECK ALL FLUID LEVELS IN ALL COMPARTMENTS; ENGINE, HYDRAULIC, FINAL DRIVES, DIFFERENTIALS, TRANSFER GEARSNormal
CHECK ALL PIVOT POINTS FOR LUBRICATION, (GREASE, OIL OR DRY LUBE)Normal
GREASE MACHINE AND NOTE WEAR, CONDITION OF AREAS GREASED, ARTICULATION, LINKAGE, PIVOT POINTS, ETCNormal
INSPECT OIL ON DIP STICKNormal
NOTE ANY OPERATIONAL NOISE, VIBRATIONS, ETCNormal
REPLACE SCREED FUEL FILTERNormal
SAFETY
BACK UP ALARM/TRAVEL ALARMNormal
BEACON LIGHT/HAZARD FLASHERSNormal
CONTROL LOCKSNormal
HORNNormal
INSPECT SEAT BELT, CONDITION AND LOG INSTALL DATE (CHANGE EVERY THREE YEARS)Normal
O&M MANUALNormal
UPON PM COMPLETION
COMPLETE CHECKLIST BEFORE LEAVING THE SITE LOCATIONNormal
DRAIN FILTER 12 HOURS BEFORE CUTTING, BAG AND FILTER MEDIA AND SEND TO MPLS/ALTOONA AS NEEDED FOR FURTHER ANALYSISNormal
ENSURE THE MAG PLUG/MAGNETIC SCREEN BAG LABEL IS FILLED OUT CORRECTLY AND COMPLETELY. SEND TO MPLS/ALTOONA AS NEEDED FOR FURTHER ANALYSISNormal
INSTALL NEW WINDOW STICKERS (PM SERVICE DUE OR ANNUAL INSPECTION), TAKE PHOTO OF WINDOW STICKERS & DOCUMENT NEXT SERVICE INFORMATIONYes
LEAVE JOB SITE CLEAN AND SAFEYes
RUN MACHINE, VERIFY NO LEAKS & ENSURE ALL CAPS ARE TIGHTLY REPLACEDNormal
TAKE PICTURES OF REPLACED FILTERS WITH LABEL OF SMU ON CANISTERPhoto Required
ARRIVAL AT SITE
CHECK CRITICAL FLUIDS (ENGINE OIL AND ANTI-FREEZE) BEFORE STARTINGNormal|
IMPLEMENT SITE SPECIFIC SAFETY MEASURES (CHOCKS, LOCK OUT TAG OUT, ETC)Normal|
PERFORM SITE SAFETY CHECKNormal|
START, OPERATE AND WARM-UP MACHINE COMPONENTS (CYCLE HYDRAULIC CYLINDERS, MOVE AROUND TO CIRCULATE FINAL DRIVE, DIFFERENTIAL AND TRANSMISSION FLUIDS). THIS MAY TAKE 5-10 MINUTES TO PERFORM. IT IS IMPORTANT TO DRAW A GOOD OIL SAMPLE FROM CIRCULATED OIL. NOTE ANY USUAL NOISES AND SMOKE.Normal|
TAKE PICTURES FROM ALL 4 CORNERS OF THE MACHINEPhoto Required|
VERIFY S/N & HOURS OF MACHINE AND SERVICE LEVEL (TAKE IMAGE OF MONITOR)Yes|
SAMPLE MACHINE
ENSURE ALL OIL SAMPLE LABELS ARE COMPLETED CORRECTLYNormal|
SUBMIT ALL SOS VIA SOS INSPECTYes|
TAKE OIL SAMPLE FROM HYDRAULIC, FINAL DRIVES, PUMP DRIVE AND AUGERNormal|
TAKE OIL SAMPLE FROM WARM ENGINENormal|
ENGINE
CHANGE ENGINE OIL AND FILTER, SAVE AND CUT FILTER AND EXAMINE FOR DEBRISNormal|
CHANGE PRIMARY AIR FILTERNormal|
CHECK COOLANT LEVEL AND FREEZE POINT. RECORD FREEZE POINT:Normal|
INSPECT AFTERCOOLERNormal|
INSPECT AIR FILTER RESTRICTION INDICATORNormal|
INSPECT AIR INTAKE SYSTEM FOR LEAKSNormal|
INSPECT ALL ENGINE DRIVE BELTS AND PULLEYSNormal|
INSPECT BELLY PAN FOR DEBRIS BUILD UPNormal|
INSPECT COOLANT HOSESNormal|
INSPECT CRANKCASE BREATHER, CLEAN IF REQUIREDNormal|
INSPECT ENGINE FOR LEAKSNormal|
INSPECT EXHAUST SYSTEMNormal|
INSPECT RADIATOR FOR DIRT BUILD UP AND LEAKSNormal|
INSPECT TURBO FOR SIGNS OF LEAKSNormal|
INSPECT WATER PUMP FOR LEAKSNormal|
REMOVE AND CLEAN/REPLACE PRIMARY FUEL FILTERNormal|
REPLACE SECONDARY FUEL FILTERNormal|
HYDRAULIC
CHANGE HYDRAULIC RETURN FILTER, CUT AND INSPECT FOR DEBRISNormal|
INSPECT HYDRAULIC CYLINDER CONDITION AND LEAKSNormal|
INSPECT HYDRAULIC HOSE/LINES CONDITION AND LEAKSNormal|
INSPECT HYDRAULIC PUMPS FOR LEAKSNormal|
FRAME/CHASSIS
CHECK FRAME AND COMPONENTS FOR CRACKS/DAMAGENormal|
CHECK FUEL TANK BREATHER AND CLEAN/REPLACENormal|
CHECK OIL LEVELS IN; HYDRAULIC PUMP DRIVE, AUGER DRIVE GEAR BOX, DRAG CONVEYOR GEAR BOXES, CHECK DEBRIS ON MAG PLUGNormal|
CHECK TRACK TENSIONERNormal|
CLEAN PAVER VENTILATION SYSTEM BLOWERNormal|
INSPECT AUGER DRIVE CHAINNormal|
INSPECT AUGER/SCREW CONVEYORNormal|
INSPECT CONVEYOR DRIVE CHAINNormal|
INSPECT ROPS/FOPS STRUCTURE, CRACKS, DAMAGE AND LOOSE HARDWAREN/A|
INSPECT STEPS, GRAB IRONS AND SHEET METAL CONDITIONNormal|
INSPECT TRACK ASSEMBLYNormal|
LUBE IDLER WHEEL BEARINGNormal|
DRIVE TRAIN
CHECK FINAL DRIVES FOR LEAKS, WEAR AND DAMAGENormal|
REPLACE FINAL DRIVE, AUGER, AND PUMP DRIVE OILNormal|
ELECTRICAL/CAB
CHECK A/C AND HEATER OPERATION, CLEAN CAB FILTERN/A|
CHECK ALL IMPLEMENT CONTROLS, WEAR AND OPERATIONNormal|
CHECK ALL OPERATING LIGHTS, HEAD,FLOOD, BRAKE, TURN AND DOMENormal|
CHECK CAB COMPONENTS, GLASS, DOOR, WINDOWS, FLOOR MAT, HANDLES, SWITCHES, AND CONTROLSN/A|
CHECK GAUGE CLUSTER FOR OPERATIONSNormal|
CHECK PRODUCT LINK OPERATIONAL STATUS, IF EQUIPPEDNormal|
CHECK SEAT, SUSPENSION, CUSHIONS AND ARM RESTS, CONDITION, LOOSENESS AND OPERATIONNormal|
DOCUMENT ANY LOGGED EVENTS/FAULT CODES FROM THE DASHNormal|
INSPECT BATTERY, CABLES AND SWITCHESNormal|
INSPECT WIPER AND WASHER FLUID PUMP, OPERATIONS, AND CONDITIONN/A|
VALIDATE HOURS AND LOCATION OF MACHINE IN VISION LINK TO ENSURE ACCURACYYes|
MISC
CHECK ALL FLUID LEVELS IN ALL COMPARTMENTS; ENGINE, HYDRAULIC, FINAL DRIVES, DIFFERENTIALS, TRANSFER GEARSNormal|
CHECK ALL PIVOT POINTS FOR LUBRICATION, (GREASE, OIL OR DRY LUBE)Normal|
GREASE MACHINE AND NOTE WEAR, CONDITION OF AREAS GREASED, ARTICULATION, LINKAGE, PIVOT POINTS, ETCNormal|
INSPECT OIL ON DIP STICKNormal|
NOTE ANY OPERATIONAL NOISE, VIBRATIONS, ETCNormal|
REPLACE SCREED FUEL FILTERNormal|
SAFETY
BACK UP ALARM/TRAVEL ALARMNormal|
BEACON LIGHT/HAZARD FLASHERSNormal|
CONTROL LOCKSNormal|
HORNNormal|
INSPECT SEAT BELT, CONDITION AND LOG INSTALL DATE (CHANGE EVERY THREE YEARS)Normal|
O&M MANUALNormal|
UPON PM COMPLETION
COMPLETE CHECKLIST BEFORE LEAVING THE SITE LOCATIONNormal|
DRAIN FILTER 12 HOURS BEFORE CUTTING, BAG AND FILTER MEDIA AND SEND TO MPLS/ALTOONA AS NEEDED FOR FURTHER ANALYSISNormal|
ENSURE THE MAG PLUG/MAGNETIC SCREEN BAG LABEL IS FILLED OUT CORRECTLY AND COMPLETELY. SEND TO MPLS/ALTOONA AS NEEDED FOR FURTHER ANALYSISNormal|
INSTALL NEW WINDOW STICKERS (PM SERVICE DUE OR ANNUAL INSPECTION), TAKE PHOTO OF WINDOW STICKERS & DOCUMENT NEXT SERVICE INFORMATIONYes|
LEAVE JOB SITE CLEAN AND SAFEYes|
RUN MACHINE, VERIFY NO LEAKS & ENSURE ALL CAPS ARE TIGHTLY REPLACEDNormal|
TAKE PICTURES OF REPLACED FILTERS WITH LABEL OF SMU ON CANISTERPhoto Required|
